感应自动门使用常识
Common sense of induction automatic door
1、人员正常速度从门外或门内走向感应门,感应自动门应该自动打开,感应自动门的动作应该平滑而且没有出现碰撞的情况;感应自动门打开后,人员以正常速度通过感应门时,感应自动门应该保持打开状态。
1. When the personnel move to the induction door from the outside or
inside of the door at normal speed, the induction automatic door shall
open automatically, and the action of the induction automatic door shall
be smooth without collision; after the induction automatic door is
opened, when the personnel pass through the induction automatic door at
normal speed, the induction automatic door shall remain open.
2、当人员离开感应自动门感应器感应区后,在延时1-10秒后(时间长短可以由感应自动门开关参数来设置),感应自动门将自动关闭,感应自动门的动作应该平滑而且没有出现碰撞的情况。
2. When the personnel leave the induction area of the induction
automatic door sensor, after a delay of 1-10 seconds (the time length
can be set by the parameters of the induction automatic door switch),
the induction automatic door will automatically close, and the action of
the induction automatic door should be smooth and there is no
collision.
3、观察正常通过感应自动门的行走路线,需要把日常行走路线调整为人员正对走向感应自动门,而不是以一定的角度走向感应自动门。
3. In order to observe the normal walking route through the induction
automatic door, it is necessary to adjust the daily walking route to the
direction of the person towards the induction automatic door, rather
than to the direction of the induction automatic door at a certain
angle.
4、走向感应自动门时,感应自动门感应器的感应宽度范围应该大于门完全打开的宽度。
4. When walking towards the induction automatic door, the induction
width range of the induction automatic door sensor shall be greater than
the width of the door fully open.
5、高档的自动平移门的控制器,都设有自动反向功能的程序:不管开启或关闭过程中,当门体运动方向上遇到障碍物或人时,门体会自动向相反方向运动。这是一个非常重要的安全、保护功能,在防止碰人或物的同时,保护感应自动门机不会因过载而烧坏。然后,门体在退回时自动执行学习程序时,不能有任何信号干扰,否则,微处理器将继续执行学习程序。如果长时间未能恢复正常,就会出现故障或功能异常。
5. The controller of high-grade automatic translation door is equipped
with the program of automatic reverse function: no matter in the process
of opening or closing, when the door body meets obstacles or people in
the moving direction, the door will automatically move in the opposite
direction. This is a very important safety and protection function,
which can protect the induction automatic door machine from burning due
to overload while preventing people or objects from being touched. Then,
when the door body automatically executes the learning program when
returning, there should be no signal interference, otherwise, the
microprocessor will continue to execute the learning program. If it
fails to return to normal for a long time, there will be fault or
abnormal function.
6、在通过人员的数量有限的环境中,自动反射功能可以作为安全性功能来防止碰人和夹人,但在大人员流量的公共区域,安全性功能应该特殊考虑。
6. In the environment with limited number of people, the automatic
reflection function can be used as a safety function to prevent people
from touching or pinching. However, in the public area with large flow
of people, the safety function should be specially considered.
7、出现异常声音和故障时,勿随意拆装泥杆 保定古筝 塑料增韧剂 拱形护坡模具 保定空调维修 托辊生产线,请及时关闭电源并与技术员联系。
7. In case of abnormal sound and failure, do not dismantle or assemble
at will. Please turn off the power supply in time and contact the
technician.
8、感应自动门轨道及吊轮不能上油;否则吊架上的滚轮有滑动现象,使门发生碰撞。
8. The induction automatic door track and lifting wheel shall not be
oiled; otherwise, the roller on the hanger will slide, causing the door
to collide.